TSURUMI PUMP

SUBMERSIBLE GENERAL DEWATERING PORTABLE PUMPS

...................

MODEL LB2-400-.LB2-400A.....................................LB2-750......

ALL LB MODELS HAVE SILICON CARBIDE FACED DOUBLE MECHANICAL SEALS, BUILT-IN MOTOR PROTECTOR ( THERMAL AND OVER CURRENT ).

COMPACT PUMPS WITH TOP DISCHARGE PROVIDES MAXIMUM MOTOR COOLING EFFICIENCY ALLOWING CONTINUOUS DUTY OPERATION AT LOW WATER LEVELS AND EXTENDED DRY-RUN CAPABILITY.

ALL LB2 MODELS ARE 2"DISCHARGE SINGLE PHASE.

OPTIONAL FLOAT SWITCH FOR AUTOMATIC OPERATION AVAILABLE.

SUBMERSIBLE SAND/TRASH HANDLING TORQUE FLOW PUMP

MODEL HS2.4S-61 1/2 HP SINGLE PHASE 115 VOLTS

SUBMERSIBLE SAND/TRASH HANDLING TORQUE FLOW PUMP. TRASH PUMP HANDLES SAND, SOLIDS, LEAVES AND DEBRI UP TO 1" X 3/8" USING A SEMI-VORTEX IMPELLER AND SHAFT MOUNTED AGITATOR.

EASY PUMP END DISASSEMBLY BY REMOVING ONLY 3 CAP NUTS.

STANDARD QUALITY FEATURES ARE SILICON CARBIDE FACED DOUBLE MECHANICAL SEALS, BUILT-IN MOTOR PROTECTOR,(THERMAL AND OVER CURRENT), CABLE CLIP TO PROTECT CABLE ENTRY.

SEMI-VORTEX DESIGN DECREASES WEAR BY MINIMIZING CONTACT WITH ABRASIVES.

URETHANE RUBBER IMPELLER AND DUCTILE IRON CASTING PUMP CASING FOR MAXIMUM DURABILITY.

OPTIONAL ACCESSORY IS THE TS-301 FLOAT SWITCH FOR AUTOMATIC OPERATION.

SUBMERSIBLE GENERAL DEWATERING TORQUE FLOW PUMP

HEAVY DUTY, HIGH HEAD PUMPS CAPABLE OF HANDLING ABRASIVE MATERIALS FOUND ON CONSTRUCTION SITES.

SEMI-VORTEX DESIGN DECREASES WEAR BY MINIMIZING CONTACT WITH ABRASIVES.

MODEL NK2-15/22 ARE 3" DISCHARGE AND HAVE ETHYLENE PROPYLENE RUBBER CASING AND WEAR PLATE FOR MAXIMUM DURABILITY. V-RING SYSTEM PROTECTS THE SHAFT SEAL FROM ABRASIVES. INTERNAL CAPACITOR START.

STANDARD QUALITY FEATURES SILICON CARBIDE FACED DOUBLE MECHANICAL SEALS, BUILT-IN MOTOR PROTECTOR ( THERMAL AND OVER CURRENT ).

OPTIONAL ACCESSORY IS THE TS-303 FLOAT SWITCH FOR AUTOMATIC OPERATION (220V ONLY) AND A SAND KIT TO SUSPEND SOLIDS AND PREVENT CLOGGING.

SUBMERSIBLE GENERAL DEWATERING LOW WATER LEVEL PUMP

CONSTRUCTION GRADE, DURABLE PUMP FOR LOW WATER PUMPING ON CIVIL ENGINEERING WORKS, ROADWAYS AND UNDERPASSES, UTILITY PITS, OR ANY GENERAL DEWATERING APPLICATION. PUMPS DOWN TO 0.2 OF AN INCH.

SYNTHETIC RUBBER WEAR PARTS AND VORTEX IMPELLER FOR MAXIMUM DURABILITY. V-RING SYSTEM PROTECTS THE SHAFT SEAL FROM ABRASIVES. TOP DISCHARGE ALLOWS CONTINUOUS DUTY LOW WATER PUMPING WITHOUT OVERHEATING MOTOR.

SILICON CARBIDE FACED DOUBLE MECHANICAL SEALS WITH BUILT IN MOTOR PROTECTOR ( THERMAL AND OVER CURRENT ).

OPTIONAL ACCESSORY IS THE TS-301 FLOAT SWITCH FOR AUTOMATIC OPERATION.

SUBMERSIBLE PROPELLER PUMP

CAST IRON PROPELLER PUMP PERFECT FOR IRRIGATION AND WATER TRANSFER APPLICATIONS.

MOTOR IS 7.7 AMP RATED 1/2 HP SINGLE PHASE 115 VOLT.

AXIAL FLOW DESIGN DELIVERS OVER 200 GPM.

THREE TIMES CAPACITY OF CONVENTIONAL 1/2 HP SUBMERSIBLE PUMPS.

CAST IRON AND STAINLESS STEEL CONSTRUCTION FOR DURABILITY.

SILICON CARBIDE FACED DOUBLE MECHANICAL SEAL WITH BUILT-IN MOTOR PROTECTOR ( THERMAL AND OVER CURRENT ).

OPTIONAL ACCESSORY IS THE TS-3-1 FLOAT SWITCH FOR AUTOMATIC OPERATION.

SUBMERSIBLE RESIDUE DEWATERING PUMP

RESIDUE DEWATERING PUMP CAPABLE OF PUMPING DOWN TO FLOOR LEVEL. EVEN THE SMALLEST PUDDLE CAN BE PUMPED DRY. IDEAL FOR COMPLETE DRAINAGE OF FLAT SURFACES WHERE A SUMP IS NOT AVAILABLE: ROOFTOPS, PARKING LOTS/GARAGES,ROADWAYS/UNDERPASS, SERVICE/UTILITY PITS, BASEMENTS, PLANT MAINTENANCE/CLEANUP, POOLS/SPAS.

INTERNAL CHECK VALVE HOLDS PRIME AND PROHIBITS BACK FLOW THROUGH PUMP.

PRIME PUMP THROUGH DISCHARGE OUTLET FOR START UP AT ANY WATER LEVEL.

HAS SILICON CARBIDE FACED DOUBLE MECHANICAL SEAL WITH BUILT-IN MOTOR PROTECTOR ( THERMAL AND OVER CURRENT ).

LET US KNOW ABOUT YOUR NEXT APPLICATION.